WEG Drives and Soft-Starters Basic Commissioning for Distributors
2024-06-12 08:00 - 2024-06-13 16:00 (America/New_York) | Marriott Courtyard, 4625 Lake Forest Dr, Blue Ash, OH, 45242, United States
This class will give fundamental tools required to install and start-up WEG low-voltage Drives and Soft Starters. Topics included will be cold power checks and wiring confirmation, programming common functions such as three-wire start, accel/decel ramp, min/max speed, electronic potentiometer, multi-speed, PID loops, etc.
Objective: Participants will receive training on WEG Low Voltage Drives and Soft Starters providing them a basic understanding of set up, operation, and Commissioning for these products.
Who should attend: WEG Distributor Sales and Drive Specialists
Prerequisites: Basic knowledge of electrical principles power electronics and control circuits. The basic ability to use multimeters, amp clamps, oscilloscopes and computers.
2023 WEG Drives and Soft Starters Basic Commissioning for Distributors Syllabus
*PLEASE DO NOT BOOK FLIGHTS OR ACCOMMODATIONS UNTIL CONFIRMATION*

Medium Voltage Service Center Training
2024-06-18 08:00 - 2024-06-21 17:00 | Online
This class will give the participant a detailed understanding of WEG MV drives for a service technician. Topics will range from troubleshooting to preventive maintenance. Through hands on training, the student will learn troubleshooting of common problems as well as replacement of common parts in the MV drive. Upon successful completion, the student will be able to troubleshoot and repair WEG MV drives in common applications.
Objectives: Train professionals to troubleshoot and repair the MV WEG drives. Participants who successfully complete the course will be authorized to troubleshoot WEG MV Drives.
Who Should Attend: WEG Authorized Automation Service Partners or those seeking to become Authorized to work with MV Drives.
Prerequisites: Knowledge of electrical principles, power electronics and control circuits. The ability to use multi-meters, amp clamps, oscilloscopes and computers. Knowledge of required safety practices and procedures. Experience with MV Drives and successfully completed WEG Low Voltage Products Service Partner Training.
Duration: 3 Days (Online)
WEG Medium Voltage Drives Troubleshooting Training for Service Centers
Training, Travel, and Housing Logistics FAQ
*PLEASE DO NOT BOOK FLIGHT OR ACCOMMODATIONS BEFORE CONFIRMATION*

Medium Voltage Service Center Training
2024-07-16 08:00 - 2024-07-18 17:00 | WEG Electric US Headquarters, 6655 Sugarloaf Parkway, Duluth, GA, 27502, United States
This class will give the participant a detailed understanding of WEG MV drives for a service technician. Topics will range from troubleshooting to preventive maintenance. Through hands on training, the student will learn troubleshooting of common problems as well as replacement of common parts in the MV drive. Upon successful completion, the student will be able to troubleshoot and repair WEG MV drives in common applications.
Objectives: Train professionals to troubleshoot and repair the MV WEG drives. Participants who successfully complete the course will be authorized to troubleshoot WEG MV Drives.
Who Should Attend: WEG Authorized Automation Service Partners or those seeking to become Authorized to work with MV Drives.
Prerequisites: Knowledge of electrical principles, power electronics and control circuits. The ability to use multi-meters, amp clamps, oscilloscopes and computers. Knowledge of required safety practices and procedures. Experience with MV Drives and successfully completed WEG Low Voltage Products Service Partner Training.
Duration: 3 Days
WEG Medium Voltage Drives Troubleshooting Training for Service Centers
Training, Travel, and Housing Logistics FAQ
*PLEASE DO NOT BOOK FLIGHT OR ACCOMMODATIONS BEFORE CONFIRMATION*

WEG Drives and Soft Starters Basic Commissioning for Distributors
2024-07-30 08:00 - 2024-07-31 17:00, 2024-08-01 08:00 - 2024-08-02 17:00 | WEG Houston Warehouse, 2031 Cypress Station Dr, Houston, TX, 77090, United States

Low Voltage Service Center Training
2024-08-19 08:00 - 2024-08-22 17:00 | WEG Electric US Headquarters, 6655 Sugarloaf Parkway, Duluth, GA, 27502, United States
This class will give the participant detailed understanding of WEG drives for a service technician. Topics will range from basic commissioning to troubleshooting and maintaining general-purpose drives. Through hands on training, the student will learn troubleshooting of common problems as well as replacement of common parts in the drive. Upon successful completion, the student will be able to commission, maintain and troubleshoot and repair WEG drives in common applications. The class is required for a certified Service Center technician.
Attendees will also be automatically enrolled in the SSW7000 Medium Voltage Soft Starter – Start-up and Troubleshooting class providing students the opportunity to control and operate the WEG SSW7000 soft-starter, understand and navigate programming hierarchy, perform oriented start-ups, and identify and troubleshoot basic faults. Participation in this class is optional, but recommended.
Objectives: Train professionals to commission, troubleshoot and repair the WEG drives, Soft Starts and Panels. Participants who successfully complete the course will be authorized to start-up WEG Low Voltage Drives and Low and Medium Voltage Soft Starters.
Who Should Attend: WEG Authorized Automation Service Partners or those seeking to become Authorized
Prerequisites: Knowledge of electrical principles, power electronics and control circuits. The ability to use multi-meters, amp clamps, oscilloscopes and computers. Knowledge of required safety practices and procedures.
Duration: 4 Days
WEG Low Voltage Products Service Partner Training Syllabus
Training, Travel, and Housing Logistics FAQ
*PLEASE DO NOT BOOK FLIGHT OR ACCOMMODATIONS BEFORE CONFIRMATION*

WEG SSW7000 Medium Voltage Soft Starter
2024-08-23 09:00 - 16:00 | WEG Electric US Headquarters, 6655 Sugarloaf Parkway, Duluth, GA, 27502, United States
This class provides in-person, hands-on, classroom training for qualified personnel to enable them to perform standard application start-ups and basic troubleshooting of WEG SSW7000 medium voltage soft-starters. The student will be able to control and operate the WEG SSW7000 soft-starter, understand and navigate programming hierarchy, perform oriented start-ups, and identify and troubleshoot basic faults.
Objective: Train professionals to control and operate the WEG SSW7000 Soft-Starter
Prerequisites: Knowledge of electrical principles, power electronics and control circuits. The ability to use multi-meters, amp clamps, oscilloscopes and computers. Understanding of safety practices regarding medium voltage.
2023 WEG SSW7000 Medium Voltage Soft Starter Training Syllabus
*PLEASE DO NOT BOOK FLIGHTS OR ACCOMMODATIONS UNTIL CONFIRMATION*

WEG SSW7000 Medium Voltage Soft Starter Training
2024-09-20 09:00 - 16:00, 2024-10-18 09:00 - 16:00, 2024-11-15 09:00 - 16:00 | WEG Electric US Headquarters, 6655 Sugarloaf Parkway, Duluth, GA, 27502, United States

Regional Training
2025-03-11 08:00 - 2025-03-14 17:00 | Sheraton Suites Chicago Elk Grove, 121 NW Point Blvd, Elk Grove Village, IL, 60007, United States
Content is protected.

Regional Training - Weimer Exclusive
2025-04-01 08:00 - 2025-04-03 17:00 | Weimer, N112 W13131 Mequon Rd, Germantown, WI, 53022, United States
Welcome to the signup for WEG Automation University Regional Training. We want to make sure you are aware of a few things before you sign up:
This event is exclusive for Weimer Bearing

You must register for the class to attend.
Regional training classes are different daily, so please select the training you’d like to attend.
Regional training requires the completion of online training before arrival to participate.
Only book your hotel or flights once you have a confirmation you are in the class and your prerequisites are completed. You will be sent an email to confirm you can do this.

Tuesday: Automation Products Selection and Sizing

Overview: This class is designed to equip you with the knowledge and skills to select and size automation products effectively. Throughout the course, you will learn how to build a combination starter, select the correct contactor, VFD, and soft start, and participate in hands-on labs to reinforce your learning.

Who Is This Class For: This training is for people looking to correctly size contactors, VFDs, and soft starts for motor control applications. It includes Inside Sales, Outside Sales, Product Specialists, and Engineers handling the design of control panels.

Wednesday & Thursday: Basic Drives and Soft Starters

Overview: This class provides hands-on training with the complete range of WEG variable frequency drives (VFDs) and soft start product offerings. Specific emphasis is focused on WEG Drive and Soft Start offerings. The class will give participants the fundamental understanding required to install and start up WEG low-voltage Drives and Soft Starters.

Who Is This Class For: This is for Product Specialists and Controls Professionals looking for hands-on experience setting up drives.

In order to be able to attend please review the list of prerequisites required to attend:
Regional Training Information and Prerequisites
***DO NOT BOOK HOTEL OR FLIGHTS UNTIL CONFIRMATION***

Regional Training
2025-05-20 08:00 - 2025-05-23 17:00 | Embassy Suites by Hilton Cleveland Rockside, 5800 Rockside Woods Blvd N, Independence, OH, 44131, United States
Welcome to the signup for WEG Automation University Regional Training. We want to make sure you are aware of a few things before you sign up:

You must register for the class to attend.
Regional training classes are different daily, so please select the training you’d like to attend.
Regional training requires the completion of online training before arrival to participate.
Only book your hotel or flights once you have a confirmation you are in the class and your prerequisites are completed. You will be sent an email to confirm you can do this.

Tuesday: Automation Products Selection and Sizing

Overview: This class is designed to equip you with the knowledge and skills to select and size automation products effectively. Throughout the course, you will learn how to build a combination starter, select the correct contactor, VFD, and soft start, and participate in hands-on labs to reinforce your learning.

Who Is This Class For: This training is for people looking to correctly size contactors, VFDs, and soft starts for motor control applications. It includes Inside Sales, Outside Sales, Product Specialists, and Engineers handling the design of control panels.
Curriculum Description

Wednesday & Thursday: Drives and Soft Starters

Overview: This class provides hands-on training with the complete range of WEG variable frequency drives (VFDs) and soft start product offerings. Specific emphasis is focused on WEG Drive and Soft Start offerings. The class will give participants the fundamental understanding required to install and start up WEG low-voltage Drives and Soft Starters.

Who Is This Class For: This is for Product Specialists and Controls Professionals looking for hands-on experience setting up drives.
Curriculum Description

Friday: Pump Genius

Overview: This hands-on training course is designed to give participants a fundamental understanding of the configuration and application of WEG’s Pump Genius. You will gain the skills needed to utilize this powerful tool effectively through practical exercises and real-world scenarios.

Who Is This Class For: This is for Product Specialists and Controls Professionals who have completed the “Basic Drives and Soft Starters” class and will be working with pump applications.
Curriculum Description

In order to be able to attend please review the list of prerequisites required to attend:
Regional Training Information and Prerequisites
***DO NOT BOOK HOTEL OR FLIGHTS UNTIL CONFIRMATION***

Regional Training
2025-06-24 08:00 - 2025-06-27 17:00 | Marriott DFW Airport North, 8440 Freeport Pkwy, Irving, Texas, 75063, United States
Welcome to the signup for WEG Automation University Regional Training. We want to make sure you are aware of a few things before you sign up:

You must register for the class to attend.
Regional training classes are different daily, so please select the training you’d like to attend.
Regional training requires the completion of online training before arrival to participate.
Only book your hotel or flights once you have a confirmation you are in the class and your prerequisites are completed. You will be sent an email to confirm you can do this.

*REGISTRATION WILL CLOSE 2 WEEKS PRIOR TO THE SCHEDULED EVENT*

Tuesday: Automation Products Selection and Sizing

Overview: This class is designed to equip you with the knowledge and skills to select and size automation products effectively. Throughout the course, you will learn how to build a combination starter, select the correct contactor, VFD, and soft start, and participate in hands-on labs to reinforce your learning.

Who Is This Class For: This training is for people looking to correctly size contactors, VFDs, and soft starts for motor control applications. It includes Inside Sales, Outside Sales, Product Specialists, and Engineers handling the design of control panels.
Curriculum Description

Wednesday & Thursday: Drives and Soft Starters

Overview: This class provides hands-on training with the complete range of WEG variable frequency drives (VFDs) and soft start product offerings. Specific emphasis is focused on WEG Drive and Soft Start offerings. The class will give participants the fundamental understanding required to install and start up WEG low-voltage Drives and Soft Starters.

Who Is This Class For: This is for Product Specialists and Controls Professionals looking for hands-on experience setting up drives.
Curriculum Description

Friday: Pump Genius

Overview: This hands-on training course is designed to give participants a fundamental understanding of the configuration and application of WEG’s Pump Genius. You will gain the skills needed to utilize this powerful tool effectively through practical exercises and real-world scenarios.

Who Is This Class For: This is for Product Specialists and Controls Professionals who have completed the “Basic Drives and Soft Starters” class and will be working with pump applications.
Curriculum Description

In order to be able to attend please review the list of prerequisites required to attend:
Regional Training Information and Prerequisites
***DO NOT BOOK HOTEL OR FLIGHTS UNTIL CONFIRMATION***

Regional Training - Air Hydro Exclusive
2025-07-08 08:00 - 2025-07-11 17:00 | Louisville KY, Louisville, KY, United States

Regional Training
2025-08-12 08:00 - 2025-08-15 17:00 | Hilton Philadelphia at Penn’s Landing, 201 S. Columbus Blvd, Philadelphia, 19106, United States

LV Drives and LV and MV SS Service Center Training.
2025-09-15 08:00 - 2025-09-19 17:00 | WEG Electric US Headquarters, 6655 Sugarloaf Parkway, Duluth, GA, 27502, United States
This class will give the participant detailed understanding of WEG drives for a service technician. Topics will range from basic commissioning to troubleshooting and maintaining general-purpose drives. Through hands on training, the student will learn troubleshooting of common problems as well as replacement of common parts in the drive. Upon successful completion, the student will be able to commission, maintain and troubleshoot and repair WEG drives in common applications. The class is required for a certified Service Center technician.
Attendees will also be automatically enrolled in the SSW7000 Medium Voltage Soft Starter – Start-up and Troubleshooting class providing students the opportunity to control and operate the WEG SSW7000 soft-starter, understand and navigate programming hierarchy, perform oriented start-ups, and identify and troubleshoot basic faults. Participation in this class is optional, but recommended.
Objectives: Train professionals to commission, troubleshoot and repair the WEG LV drives, Soft Starts and Panels and MV Soft Staters. Participants who successfully complete the course will be authorized to start-up WEG Low Voltage Drives and Low and Medium Voltage Soft Starters.
Who Should Attend: WEG Authorized Automation Service Partners or those seeking to become Authorized
Prerequisites: Knowledge of electrical principles, power electronics and control circuits. The ability to use multi-meters, amp clamps, oscilloscopes and computers. Knowledge of required safety practices and procedures.
Duration: 5 Days
WEG Low Voltage Products Service Partner Training Syllabus
Training, Travel, and Housing Logistics FAQ
*PLEASE DO NOT BOOK FLIGHT OR ACCOMMODATIONS BEFORE CONFIRMATION*

Regional Training
2025-09-23 08:00 - 2025-09-24 17:00 | DoubleTree by Hilton Cincinnati Airport, 2826 Terminal Drive, Hebron, KY, 41048, United States
Welcome to the signup for WEG Automation University Regional Training. We want to make sure you are aware of a few things before you sign up:

You must register for the class to attend.
Regional training classes are different daily, so please select the training you’d like to attend.
Regional training requires the completion of online training before arrival to participate.
Only book your hotel or flights once you have a confirmation you are in the class and your prerequisites are completed. You will be sent an email to confirm you can do this.

Tuesday & Wednesday: Drives and Soft Starters

Overview: This class provides hands-on training with the complete range of WEG variable frequency drives (VFDs) and soft start product offerings. Specific emphasis is focused on WEG Drive and Soft Start offerings. The class will give participants the fundamental understanding required to install and start up WEG low-voltage Drives and Soft Starters.

Who Is This Class For: This is for Product Specialists and Controls Professionals looking for hands-on experience setting up drives.
Curriculum Description

In order to be able to attend please review the list of prerequisites required to attend:
Regional Training Information and Prerequisites
***DO NOT BOOK HOTEL OR FLIGHTS UNTIL CONFIRMATION***

Houston Regional Training
2025-10-21 08:00 - 2025-10-24 17:00 | Hyatt Regency Houston West, 13210 Katy Freeway, Houston, TX, 77079, United States

Las Vegas Regional Training November 11-14, 2025
2025-11-11 08:00 - 2025-11-14 17:00 | DoubleTree by Hilton Las Vegas Airport, 7250 Pollock Dr, Las Vegas, 89119, United States

Medium Voltage Drives & Soft-Starters Programming/Installation - Online Training via Microsoft Teams
2026-02-16 08:00 - 2026-02-20 17:00 | Microsoft Teams
This course provides participants with a comprehensive understanding of WEG medium-voltage drives and soft starters from a service and commissioning perspective. Designed for technicians and engineers, the training covers installation, programming, preventive maintenance, and troubleshooting of WEG MV products, including MVW-01, MVW-01 G4, MVW3000, MVW3000 G4, and the SSW7000 soft starter.
Participants will gain hands-on knowledge navigating HMI interfaces, reading and diagnosing parameters, performing oriented start-ups, and identifying and resolving common faults and alarms. Upon successful completion, students will be prepared to commission, maintain, and troubleshoot WEG medium-voltage drives and soft starters in common industrial applications.
Objectives

Train professionals to troubleshoot and service WEG medium-voltage drives and soft starters
Build confidence in diagnostics and preventative maintenance for MV applications

Who Should Attend

Technicians or engineers with experience in low- or medium-voltage drives and soft starters

WEG Authorized Automation Service Partners or those seeking authorization

Prerequisites
**In order to attend, participants must complete and submit this form: WEG Drives and Softstarters Application Form **

Module 1 (LV – Online) completion, or

Minimum one year of experience with low-voltage drives and soft starters (any brand), or

Minimum one year of experience with medium-voltage drives and soft starters (any brand)

Training Format

Online

Total training time: 24 hours

Required materials:

Laptop with webcam and microphone

LV Drives and LV and MV SS Service Center Training.
2026-02-23 08:30 - 2026-02-27 16:00, 2026-04-20 08:30 - 2026-04-24 16:00, 2026-06-22 08:30 - 2026-06-26 16:00 | WEG Electric US Headquarters, 6655 Sugarloaf Parkway, Duluth, GA, 27502, United States
This class provides Authorized WEG Automation Distributors an overview of the complete WEG Automation product offers including overview of available tools and resources to assist in specification and selling efforts. Specific emphasis is focused on WEG Drive and Soft Starter offers.
The class will give participants the fundamental understanding required to install and start-up WEG low-voltage Drives and Soft Starters. Topics included; cold power checks and wiring confirmation, programming common functions such as three-wire start, accel/decel ramp, min/max speed, electronic potentiometer, multi-speed, PID loops, and other application specific topics.
Participants will receive training on the configuration and application of WEG’s Pump Genius software including basic set up of the Pump Genius system and use of the Pump Genius wizard. With hands on demos the student will learn how to set up simplex and multiplex pump systems, set up process set point and feedback control loops, configure for direct and reverse control, and set up and troubleshooting of faults and alarms.
Attendees will also be automatically enrolled in the SSW7000 Medium Voltage Soft Starter – Start-up and Troubleshooting class providing students the opportunity to control and operate the WEG SSW7000 soft-starter, understand and navigate programming hierarchy, perform oriented start-ups, and identify and troubleshoot basic faults. Participation in this class is optional, but recommended.
Objective: Provide Authorized WEG Automation Distributor Specialists the commercial and technical training needed to select, sell and technically apply WEG Automation offers. Participants who successfully complete the course will be authorized to start-up WEG Low Voltage Drives and Low and Medium Voltage Soft Starters.
Who should attend: WEG Distributor Drive Specialists who meet the identified program prerequisites listed below
Prerequisites: Completion and approval of the Automation Service Candidate Registration Form and WEG visit to candidate facility.
To begin the process please complete this form: Candidate Registration Form
Duration: 5 Days
WEG Automation Distributor Drives Specialist Training Syllabus
Training, Travel, and Housing Logistics FAQ
*PLEASE DO NOT BOOK FLIGHTS OR HOTEL UNTIL CONFIRMATION*

Medium Voltage Drives & Soft-Starters Programming/Installation – Online Training via Microsoft Teams
2026-04-13 08:00 - 2026-04-17 17:00 | Microsoft Teams

Duluth, GA - Regional Training
2026-05-05 08:00 - 2026-05-08 17:00 | WEG Electric US Headquarters, 6655 Sugarloaf Parkway, Duluth, GA, 27502, United States
Welcome to the signup for WEG Automation University Regional Training.
Please review the following important information before registering:

Registration is required to attend any class.
Two (2) training rooms will be running concurrently, so please ensure you do not select classes with overlapping times.
If a class appears more than once on the schedule, it is being offered multiple times during the week.
Completion of required online training is mandatory prior to attending in-person regional training.
Do not book travel or lodging until you receive confirmation that you are enrolled in the class and all prerequisites have been completed. A confirmation email will be sent once you are cleared to proceed.

Schedule for Week

Room Tuesday Wednesday Thursday Friday

Room 1 Drives & Soft Starters Pump Genius
Room 2 WEG Automation Products Selection and Sizing (Session 1) WEG Automation Products Selection and Sizing (Session 2) TPD500 Installation and Programming

Class Descriptions

Tuesday or Wednesday: Product Selection & Sizing

Duration:
One (1) day
Overview:
Learn how to select and size automation products effectively. This course covers combination starters, contactors, VFDs, soft starters and more. This class is reinforced through hands-on labs.

Session Details
Prerequisites
Class Topics
Class Format

Who Is This Class For:
Inside sales, outside sales, product specialists, and engineers involved in motor control and panel design.

The student completed the following online classes before attending training:

Electrical Basics
Electrical Safety
Electrical Drawings
Common Standards
Basics of Circuit Protection
Power Factor Basics
Motor Starting Methods
Soft Start Basics
VFD Basics
Motor Basics
WEG Control Product Overview
WEG Drives and Soft Starter Overview

This is approximately six (6) hours of online training.

COURSE OBJECTIVES: Upon completion of this course, students will be able to:

Select the best motor control solution for your application.
Properly size a VFD
Properly size a soft starter
Learn available tools and resources to assist in specification and selling efforts.

TOPICS

Selecting the correct contactor and accessories
Assembling a contactor
Selecting the correct variable frequency drive (VFD)
Selecting the correct soft starter

This one (1) day course is conducted from 8:00 a.m. to 5:00 p.m. and includes a 30 minute lunch break. The training format is designed to balance theory and application, with approximately 70% instructor-led lecture and 30% hands-on exercises.

Tuesday & Wednesday: Drives & Soft Starters

Duration:
Two (2) days
Overview:
Hands-on training covering WEG VFDs and soft starters, focusing on installation, startup, and configuration of low-voltage drives.This class is only for the CFW and SSW product lines.

Session Details
Prerequisites
Class Topics
Class Format

Who Is This Class For:
Product specialists and controls professionals seeking hands-on drive setup experience.

WEG Training Safety Policy
WEG offers a variety of training classes that involve hands-on work with low-level voltages (120 VAC, 208 VAC, and 460 VAC). To safeguard participants during these sessions, WEG adheres to an Arc Flash Policy aligned with the standards set forth in NFPA 70E.

As part of these safety requirements, all students must wear non-melting, untreated, natural fiber long pants while attending class. This clothing standard is mandatory to ensure personal protection when working with training equipment.

The student completed the following WEG Automation University online classe before attending training:

Electrical Basics
Electrical Safety
Basics of Circuit Protection
Motor Starting Methods
Soft Start Basics
VFD Basics
Motor Basics
WEG Drives and Soft Starter Overview
SSW05 Product Overview
SSW07 Product Overview
SSW900 Product Overview
CFW11 Product Overview
CFW100 Product Overview
CFW320 Product Overview
CFW500 Product Overview
CFW900 Product Overview

This is approximately eight (8) hours of online training.

COURSE OBJECTIVES: Upon completion of this course, students will be able to:

Control and operate the WEG family of drives and soft starters
Understand and navigate the programming hierarchy
Perform oriented start-ups
Use of WEG WPS software
Identify and troubleshoot faults

TOPICS

Soft Starters (SSW07 & SSW900 Focused)
Drives (CFW320, CFW500, & CFW900 Focused)
HMI Navigation
Oriented start-up
Basic parameters
PID control
Networking Basics
Fault descriptions and troubleshooting
Using WEG WPS software

This two(2) day course is conducted from 8:00 a.m. to 5:00 p.m. and includes a 30 miute lunch break each day. The training format is designed to balance theory and application, with approximately 30% instructor-led lecture and 70% hands-on exercises.

Optional: Authorized start-up for WEG Low Voltage Drives and Low Voltage Soft Starters. To participate, you must:

Be an authorized WEG distributor, system integrator, or OEM.
Complete the in-person hands-on test at the end of class. The test takes up to 2 hours to complete, but most people complete it in under 1 hour.
Complete a computer-based test within 30 days of completing the class, which can take up to an additional 2 hours.

Thursday & Friday: Pump Genius

.
Duration:
Two (2) days
Overview:
Learn configuration and application of WEG’s Pump Genius through practical exercises. This class will cover Pump Genius on the CFW11, CFW320, CFW500, and CFW900.

Session Details
Prerequisites
Class Topics
Class Format

Who Is This Class For:
Product specialists and controls professionals who have completed Basic Drives & Soft Starters.

WEG Training Safety Policy
WEG offers a variety of training classes that involve hands-on work with low-level voltages (120 VAC, 208 VAC, and 460 VAC). To safeguard participants during these sessions, WEG adheres to an Arc Flash Policy aligned with the standards set forth in NFPA 70E.

As part of these safety requirements, all students must wear non-melting, untreated, natural fiber long pants while attending class. This clothing standard is mandatory to ensure personal protection when working with training equipment.

The student completed the following WEG Automation University online classes before attending training:

Pump Genius Basics
How a Centrifugal Pump Works

This is approximately one (1) hour of online training.

COURSE OBJECTIVES: Upon completion of this course, students will be able to:

Use WEG WPS and WLP software for Pump Genius
Setup Pump Genius for Simplex, Multipump, and Multiplex Pump Genius on the CFW500 and CFW900.
Identify and troubleshoot faults.

TOPICS

Overview of Pump Genius in WPS and WLP software
Overview of the CFW500 and CFW900 Simplex System
Overview of the CFW500 and CFW900 Multipump System
Overview of the CFW500 and CFW900 Multiplex System
Features of Pump Genius on the CFW320 & CFW11

This two(2) day course is conducted from 8:00 a.m. to 5:00 p.m. and includes a 30 minute lunch break each day. The training format is designed to balance theory and application, with approximately 30% instructor-led lecture and 70% hands-on exercises.

Optional: Authorized start-up for WEG Low Voltage Drives and Low Voltage Soft Starters. To participate, you must:

Be an authorized WEG distributor, system integrator, or OEM.
Complete the in-person hands-on test at the end of class. The test takes up to 2 hours to complete, but most people complete it in under 1 hour.
Complete a computer-based test within 30 days of completing the class, which can take up to an additional 2 hours.

Thursday & Friday: TPD500 Installation & Programming

Duration:
2 days
Overview:
This course equips participants with the knowledge and practical skills to configure, operate, and maintain the WEG TPD500 DC drive system. The training blends classroom instruction with hands-on exercises.
To attend this course you must be an authorized TPD partner.

Session Details
Prerequisites
Class Topics
Class Format

Who Is This Class For:
Product specialists and controls professionals seeking hands-on DC Drive experience.

WEG Training Safety Policy
WEG offers a variety of training classes that involve hands-on work with low-level voltages (120 VAC, 208 VAC, and 460 VAC). To safeguard participants during these sessions, WEG adheres to an Arc Flash Policy aligned with the standards set forth in NFPA 70E.

As part of these safety requirements, all students must wear non-melting, untreated, natural fiber long pants while attending class. This clothing standard is mandatory to ensure personal protection when working with training equipment.

The student completed the following WEG Automation University online classes before attending training:

Electrical Basics
Electrical Safety
Electrical Drawings
Common Standards
Basics of Circuit Protection
Motor Basics
DC Motor Basics
WEG TPD500 Overview

This is approximately five (5) hours of online training.

COURSE OBJECTIVES: Upon successful completion of this course, participants will be able to:

Learn how to select, configure, and maintain TPD500 drives
Know how to use WEG_Express software for drive configuration, monitoring, and diagnostics
Learn how to perform effective troubleshooting and maintenance procedures to reduce downtime
Implement control strategies for common DC motor applications, including winder systems

TOPICS

Overview of WEG_Express software
Overview of the TPD500 family of drives
HMI Navigation
Basic parameters
Fault descriptions and troubleshooting

This two(2) day course is conducted from 8:00 a.m. to 5:00 p.m. and includes a 30 minute lunch break each day. The training format is designed to balance theory and application, with approximately 30% instructor-led lecture and 70% hands-on exercises.

Optional: Authorized start-up for the WEG TPD500. To participate, you must:

Be an authorized WEG distributor, system integrator, or OEM.
Complete the in-person hands-on test at the end of class. The test takes up to 2 hours to complete, but most people complete it in under 1 hour.
Complete a computer-based test within 30 days of completing the class, which can take up to an additional 2 hours.

Need More Help? Click here for Training Event Support

*** DO NOT BOOK ANY TRAVEL UNTIL YOU RECIVE CONFIRMATION EMAIL ***

You will receive an email 3-4 weeks before the event confirming the event. If you register less than 4 weeks before the event you will be notified as soon as possible.
All travel costs including but not limited to flights, car rentals, hotel, and meals not during training are the responsibility of the attendee.

Chicago, IL - Regional Training
2026-07-07 09:00 - 2026-07-10 18:00 | Westin Chicago Northwest, 400 Park Blvd., Itasca, IL, 60143, United States

LV Drives and LV and MV SS Service Center Training.
2026-08-24 08:30 - 2026-08-28 16:00 | WEG Electric US Headquarters, 6655 Sugarloaf Parkway, Duluth, GA, 27502, United States
This class will give the participant detailed understanding of WEG drives for a service technician. Topics will range from basic commissioning to troubleshooting and maintaining general-purpose drives. Through hands on training, the student will learn troubleshooting of common problems as well as replacement of common parts in the drive. Upon successful completion, the student will be able to commission, maintain and troubleshoot and repair WEG drives in common applications. The class is required for a certified Service Center technician.
Attendees will also be automatically enrolled in the SSW7000 Medium Voltage Soft Starter – Start-up and Troubleshooting class providing students the opportunity to control and operate the WEG SSW7000 soft-starter, understand and navigate programming hierarchy, perform oriented start-ups, and identify and troubleshoot basic faults. Participation in this class is optional, but recommended.
Objectives: Train professionals to commission, troubleshoot and repair the WEG LV drives, Soft Starts and Panels and MV Soft Staters. Participants who successfully complete the course will be authorized to start-up WEG Low Voltage Drives and Low and Medium Voltage Soft Starters.
Who Should Attend: WEG Authorized Automation Service Partners or those seeking to become Authorized
Prerequisites: Completion and approval of the Automation Service Candidate Registration Form and WEG visit to candidate facility.
To begin the process please complete this form: Candidate Registration Form
.
Duration: 5 Days
WEG Low Voltage Products Service Partner Training Syllabus
Training, Travel, and Housing Logistics FAQ
*PLEASE DO NOT BOOK FLIGHT OR ACCOMMODATIONS BEFORE CONFIRMATION*

Boston, MA - Regional Training
2026-09-21 08:00 - 2026-09-24 17:00 | The Westin Waltham Boston, 70 Third Avenue, Waltham, 02451, United States
Welcome to the signup for WEG Automation University Regional Training.
Please review the following important information before registering:

Registration is required to attend any class.
Two (2) training rooms will be running concurrently, so please ensure you do not select classes with overlapping times.
If a class appears more than once on the schedule, it is being offered multiple times during the week.
Completion of required online training is mandatory prior to attending in-person regional training.
Do not book travel or lodging until you receive confirmation that you are enrolled in the class and all prerequisites have been completed. A confirmation email will be sent once you are cleared to proceed.

Schedule for Week

RoomMonday Tuesday Wednesday Thursday Friday

Room 1 WEG Automation Products Selection and Sizing Drives & Soft Starters Pump Genius
Room 2 TPD500 Installation and Programming

Class Descriptions

Monday: Product Selection & Sizing

Duration:
One (1) day
Overview:
Learn how to select and size automation products effectively. This course covers combination starters, contactors, VFDs, soft starters and more. This class is reinforced through hands-on labs.

Session Details
Prerequisites
Class Topics
Class Format

Who Is This Class For:
Inside sales, outside sales, product specialists, and engineers involved in motor control and panel design.

The student completed the following online classes before attending training:

Electrical Basics
Electrical Safety
Electrical Drawings
Common Standards
Basics of Circuit Protection
Power Factor Basics
Motor Starting Methods
Soft Start Basics
VFD Basics
Motor Basics
WEG Control Product Overview
WEG Drives and Soft Starter Overview

This is approximately six (6) hours of online training.

COURSE OBJECTIVES: Upon completion of this course, students will be able to:

Select the best motor control solution for your application.
Properly size a VFD
Properly size a soft starter
Learn available tools and resources to assist in specification and selling efforts.

TOPICS

Selecting the correct contactor and accessories
Assembling a contactor
Selecting the correct variable frequency drive (VFD)
Selecting the correct soft starter

This one (1) day course is conducted from 8:00 a.m. to 5:00 p.m. and includes a 30 minute lunch break. The training format is designed to balance theory and application, with approximately 70% instructor-led lecture and 30% hands-on exercises.

Tuesday & Wednesday: Drives & Soft Starters

Duration:
Two (2) days
Overview:
Hands-on training covering WEG VFDs and soft starters, focusing on installation, startup, and configuration of low-voltage drives.This class is only for the CFW and SSW product lines.

Session Details
Prerequisites
Class Topics
Class Format

Who Is This Class For:
Product specialists and controls professionals seeking hands-on drive setup experience.

WEG Training Safety Policy
WEG offers a variety of training classes that involve hands-on work with low-level voltages (120 VAC, 208 VAC, and 460 VAC). To safeguard participants during these sessions, WEG adheres to an Arc Flash Policy aligned with the standards set forth in NFPA 70E.

As part of these safety requirements, all students must wear non-melting, untreated, natural fiber long pants while attending class. This clothing standard is mandatory to ensure personal protection when working with training equipment.

The student completed the following WEG Automation University online classe before attending training:

Electrical Basics
Electrical Safety
Basics of Circuit Protection
Motor Starting Methods
Soft Start Basics
VFD Basics
Motor Basics
WEG Drives and Soft Starter Overview
SSW05 Product Overview
SSW07 Product Overview
SSW900 Product Overview
CFW11 Product Overview
CFW100 Product Overview
CFW320 Product Overview
CFW500 Product Overview
CFW900 Product Overview

This is approximately eight (8) hours of online training.

COURSE OBJECTIVES: Upon completion of this course, students will be able to:

Control and operate the WEG family of drives and soft starters
Understand and navigate the programming hierarchy
Perform oriented start-ups
Use of WEG WPS software
Identify and troubleshoot faults

TOPICS

Soft Starters (SSW07 & SSW900 Focused)
Drives (CFW320, CFW500, & CFW900 Focused)
HMI Navigation
Oriented start-up
Basic parameters
PID control
Networking Basics
Fault descriptions and troubleshooting
Using WEG WPS software

This two(2) day course is conducted from 8:00 a.m. to 5:00 p.m. and includes a 30 miute lunch break each day. The training format is designed to balance theory and application, with approximately 30% instructor-led lecture and 70% hands-on exercises.

Optional: Authorized start-up for WEG Low Voltage Drives and Low Voltage Soft Starters. To participate, you must:

Be an authorized WEG distributor, system integrator, or OEM.
Complete the in-person hands-on test at the end of class. The test takes up to 2 hours to complete, but most people complete it in under 1 hour.
Complete a computer-based test within 30 days of completing the class, which can take up to an additional 2 hours.

Thursday & Friday: Pump Genius

.
Duration:
Two (2) days
Overview:
Learn configuration and application of WEG’s Pump Genius through practical exercises. This class will cover Pump Genius on the CFW11, CFW320, CFW500, and CFW900.

Session Details
Prerequisites
Class Topics
Class Format

Who Is This Class For:
Product specialists and controls professionals who have completed Basic Drives & Soft Starters.

WEG Training Safety Policy
WEG offers a variety of training classes that involve hands-on work with low-level voltages (120 VAC, 208 VAC, and 460 VAC). To safeguard participants during these sessions, WEG adheres to an Arc Flash Policy aligned with the standards set forth in NFPA 70E.

As part of these safety requirements, all students must wear non-melting, untreated, natural fiber long pants while attending class. This clothing standard is mandatory to ensure personal protection when working with training equipment.

The student completed the following WEG Automation University online classes before attending training:

Pump Genius Basics
How a Centrifugal Pump Works

This is approximately one (1) hour of online training.

COURSE OBJECTIVES: Upon completion of this course, students will be able to:

Use WEG WPS and WLP software for Pump Genius
Setup Pump Genius for Simplex, Multipump, and Multiplex Pump Genius on the CFW500 and CFW900.
Identify and troubleshoot faults.

TOPICS

Overview of Pump Genius in WPS and WLP software
Overview of the CFW500 and CFW900 Simplex System
Overview of the CFW500 and CFW900 Multipump System
Overview of the CFW500 and CFW900 Multiplex System
Features of Pump Genius on the CFW320 & CFW11

This two(2) day course is conducted from 8:00 a.m. to 5:00 p.m. and includes a 30 minute lunch break each day. The training format is designed to balance theory and application, with approximately 30% instructor-led lecture and 70% hands-on exercises.

Optional: Authorized start-up for WEG Low Voltage Drives and Low Voltage Soft Starters. To participate, you must:

Be an authorized WEG distributor, system integrator, or OEM.
Complete the in-person hands-on test at the end of class. The test takes up to 2 hours to complete, but most people complete it in under 1 hour.
Complete a computer-based test within 30 days of completing the class, which can take up to an additional 2 hours.

Thursday & Friday: TPD500 Installation & Programming

Duration:
2 days
Overview:
This course equips participants with the knowledge and practical skills to configure, operate, and maintain the WEG TPD500 DC drive system. The training blends classroom instruction with hands-on exercises.
To attend this course you must be an authorized TPD partner.

Session Details
Prerequisites
Class Topics
Class Format

Who Is This Class For:
Product specialists and controls professionals seeking hands-on DC Drive experience.

WEG Training Safety Policy
WEG offers a variety of training classes that involve hands-on work with low-level voltages (120 VAC, 208 VAC, and 460 VAC). To safeguard participants during these sessions, WEG adheres to an Arc Flash Policy aligned with the standards set forth in NFPA 70E.

As part of these safety requirements, all students must wear non-melting, untreated, natural fiber long pants while attending class. This clothing standard is mandatory to ensure personal protection when working with training equipment.

The student completed the following WEG Automation University online classes before attending training:

Electrical Basics
Electrical Safety
Electrical Drawings
Common Standards
Basics of Circuit Protection
Motor Basics
DC Motor Basics
WEG TPD500 Overview

This is approximately five (5) hours of online training.

COURSE OBJECTIVES: Upon successful completion of this course, participants will be able to:

Learn how to select, configure, and maintain TPD500 drives
Know how to use WEG_Express software for drive configuration, monitoring, and diagnostics
Learn how to perform effective troubleshooting and maintenance procedures to reduce downtime
Implement control strategies for common DC motor applications, including winder systems

TOPICS

Overview of WEG_Express software
Overview of the TPD500 family of drives
HMI Navigation
Basic parameters
Fault descriptions and troubleshooting

This two(2) day course is conducted from 8:00 a.m. to 5:00 p.m. and includes a 30 minute lunch break each day. The training format is designed to balance theory and application, with approximately 30% instructor-led lecture and 70% hands-on exercises.

Optional: Authorized start-up for the WEG TPD500. To participate, you must:

Be an authorized WEG distributor, system integrator, or OEM.
Complete the in-person hands-on test at the end of class. The test takes up to 2 hours to complete, but most people complete it in under 1 hour.
Complete a computer-based test within 30 days of completing the class, which can take up to an additional 2 hours.

Need More Help? Click here for Training Event Support

*** DO NOT BOOK ANY TRAVEL UNTIL YOU RECIVE CONFIRMATION EMAIL ***

You will receive an email 3-4 weeks before the event confirming the event. If you register less than 4 weeks before the event you will be notified as soon as possible.
All travel costs including but not limited to flights, car rentals, hotel, and meals not during training are the responsibility of the attendee.

LV Drives and LV and MV SS Service Center Training.
2026-10-26 08:30 - 2026-10-30 16:00 | WEG Electric US Headquarters, 6655 Sugarloaf Parkway, Duluth, GA, 27502, United States
This class will give the participant detailed understanding of WEG drives for a service technician. Topics will range from basic commissioning to troubleshooting and maintaining general-purpose drives. Through hands on training, the student will learn troubleshooting of common problems as well as replacement of common parts in the drive. Upon successful completion, the student will be able to commission, maintain and troubleshoot and repair WEG drives in common applications. The class is required for a certified Service Center technician.
Attendees will also be automatically enrolled in the SSW7000 Medium Voltage Soft Starter – Start-up and Troubleshooting class providing students the opportunity to control and operate the WEG SSW7000 soft-starter, understand and navigate programming hierarchy, perform oriented start-ups, and identify and troubleshoot basic faults. Participation in this class is optional, but recommended.
Objectives: Train professionals to commission, troubleshoot and repair the WEG LV drives, Soft Starts and Panels and MV Soft Staters. Participants who successfully complete the course will be authorized to start-up WEG Low Voltage Drives and Low and Medium Voltage Soft Starters.
Who Should Attend: WEG Authorized Automation Service Partners or those seeking to become Authorized
Prerequisites: Completion and approval of the Automation Service Candidate Registration Form and WEG visit to candidate facility.
To begin the process please complete this form: Candidate Registration Form
Duration: 5 Days
WEG Low Voltage Products Service Partner Training Syllabus
Training, Travel, and Housing Logistics FAQ
*PLEASE DO NOT BOOK FLIGHT OR ACCOMMODATIONS BEFORE CONFIRMATION*
