Columbus Ohio Regional Training April 8-12, 2027

Who Is This Class For: Inside sales, outside sales, product specialists, and engineers involved in motor control and panel design.

The student completed the following online classes before attending training:

• Electrical Basics
• Electrical Safety
• Electrical Drawings
• Common Standards
• Basics of Circuit Protection
• Power Factor Basics
• Motor Starting Methods
• Soft Start Basics
• VFD Basics
• Motor Basics
• WEG Control Product Overview
• WEG Drives and Soft Starter Overview

This is approximately six (6) hours of online training.

COURSE OBJECTIVES: Upon completion of this course, students will be able to:

• Select the best motor control solution for your application.
• Properly size a VFD
• Properly size a soft starter
• Learn available tools and resources to assist in specification and selling efforts.

TOPICS

• Selecting the correct contactor and accessories
• Assembling a contactor
• Selecting the correct variable frequency drive (VFD)
• Selecting the correct soft starter

This one (1) day course is conducted from 8:00 a.m. to 5:00 p.m. and includes a 30 minute lunch break. The training format is designed to balance theory and application, with approximately 70% instructor-led lecture and 30% hands-on exercises.

Who Is This Class For: Product specialists and controls professionals seeking hands-on drive setup experience.

WEG Training Safety Policy WEG offers a variety of training classes that involve hands-on work with low-level voltages (120 VAC, 208 VAC, and 460 VAC). To safeguard participants during these sessions, WEG adheres to an Arc Flash Policy aligned with the standards set forth in NFPA 70E. As part of these safety requirements, all students must wear non-melting, untreated, natural fiber long pants while attending class. This clothing standard is mandatory to ensure personal protection when working with training equipment.

The student completed the following WEG Automation University online classe before attending training:

• Electrical Basics
• Electrical Safety
• Basics of Circuit Protection
• Motor Starting Methods
• Soft Start Basics
• VFD Basics
• Motor Basics
• WEG Drives and Soft Starter Overview
• SSW05 Product Overview
• SSW07 Product Overview
• SSW900 Product Overview
• CFW11 Product Overview
• CFW100 Product Overview
• CFW320 Product Overview
• CFW500 Product Overview
• CFW900 Product Overview

This is approximately eight (8) hours of online training.

COURSE OBJECTIVES: Upon completion of this course, students will be able to:

• Control and operate the WEG family of drives and soft starters
• Understand and navigate the programming hierarchy
• Perform oriented start-ups
• Use of WEG WPS software
• Identify and troubleshoot faults

TOPICS

• Soft Starters (SSW07 & SSW900 Focused)
• Drives (CFW320, CFW500, & CFW900 Focused)
• HMI Navigation
• Oriented start-up
• Basic parameters
• PID control
• Networking Basics
• Fault descriptions and troubleshooting
• Using WEG WPS software

This two(2) day course is conducted from 8:00 a.m. to 5:00 p.m. and includes a 30 miute lunch break each day. The training format is designed to balance theory and application, with approximately 30% instructor-led lecture and 70% hands-on exercises.

Optional: Authorized start-up for WEG Low Voltage Drives and Low Voltage Soft Starters. To participate, you must:

• Be an authorized WEG distributor, system integrator, or OEM.
• Complete the in-person hands-on test at the end of class. The test takes up to 2 hours to complete, but most people complete it in under 1 hour.
• Complete a computer-based test within 30 days of completing the class, which can take up to an additional 2 hours.

Who Is This Class For: Product specialists and controls professionals who have completed Basic Drives & Soft Starters.

WEG Training Safety Policy: WEG offers a variety of training classes that involve hands-on work with low-level voltages (120 VAC, 208 VAC, and 460 VAC). To protect participants during these sessions, WEG follows an Arc Flash Policy aligned with NFPA 70E standards.

As part of these safety requirements, all students must wear non-melting, untreated, natural fiber long pants while attending class. This clothing standard is mandatory to protect students when working with training equipment.

The student must complete the following WEG Automation University online classes before attending training:

• Electrical Basics
• Electrical Safety
• Basics of Circuit Protection
• Motor Starting Methods
• VFD Basics
• Motor Basics
• ADV200 Product Overview

This is approximately six (6) hours of online training.

COURSE OBJECTIVES: Upon completion of this course, students will be able to:

• Select and size the correct ADV200
• Control and operate the ADV200
• Use WEG_DriveLabs
• Perform an oriented startup
• Identify and troubleshoot faults

TOPICS

• Overview & Selection of the ADV200 Product Line
• Installation of the ADV200
• Programming the ADV200

This is a two (2) day course. Day 1 runs from 8:00 a.m. to 5:00 p.m., and Day 2 runs from 8:00 a.m. to 5:00 p.m. The training format is designed to balance theory and application, with approximately 30% instructor-led lecture and 70% hands-on exercises.

Optional: Authorized start-up for WEG ADV200 Drives. To participate, you must:

• Be an authorized WEG distributor, system integrator, or OEM.
• Complete the in-person hands-on test at the end of class. The test takes up to 2 hours, but most people complete it in under 1 hour.

Who Is This Class For: Product specialists and controls professionals who have completed Basic Drives & Soft Starters.

WEG Training Safety Policy WEG offers a variety of training classes that involve hands-on work with low-level voltages (120 VAC, 208 VAC, and 460 VAC). To safeguard participants during these sessions, WEG adheres to an Arc Flash Policy aligned with the standards set forth in NFPA 70E. As part of these safety requirements, all students must wear non-melting, untreated, natural fiber long pants while attending class. This clothing standard is mandatory to ensure personal protection when working with training equipment.

The student completed the following WEG Automation University online classes before attending training:

• Pump Genius Basics
• How a Centrifugal Pump Works

This is approximately one (1) hour of online training.

COURSE OBJECTIVES: Upon completion of this course, students will be able to:

• Use WEG WPS and WLP software for Pump Genius
• Setup Pump Genius for Simplex, Multipump, and Multiplex Pump Genius on the CFW500 and CFW900.
• Identify and troubleshoot faults.

TOPICS

• Overview of Pump Genius in WPS and WLP software
• Overview of the CFW500 and CFW900 Simplex System
• Overview of the CFW500 and CFW900 Multipump System
• Overview of the CFW500 and CFW900 Multiplex System
• Features of Pump Genius on the CFW320 & CFW11

This two(2) day course is conducted from 8:00 a.m. to 5:00 p.m. and includes a 30 minute lunch break each day. The training format is designed to balance theory and application, with approximately 30% instructor-led lecture and 70% hands-on exercises.

Optional: Authorized start-up for WEG Low Voltage Drives and Low Voltage Soft Starters. To participate, you must:

• Be an authorized WEG distributor, system integrator, or OEM.

Session Details: This is a four (4) hour class on April 12, 2027, from 1:00 p.m. to 5:00 p.m. Students are welcome to attend lunch at 12:00 p.m.

Who Is This Class For: Product specialists and controls professionals who want to learn more about CODESYS®. Previous PLC experience is highly recommended for this class.

The student must complete the following WEG Automation University online class before attending training:

• PLC & HMI Overview

This is approximately 20 minutes of online training.

COURSE OBJECTIVES: Upon completion of this course, students will be able to:

• Have a basic understanding of the CODESYS® platform
• Understand the features available through CODESYS

TOPICS

• CODESYS Resources
• Data persistence
• Introduction to library development
• OPC-UA Communications
• Security
• Debugging & Troubleshooting

This is a four (4) hour course running from 1:00 p.m. to 5:00 p.m. on Monday, April 12, 2027. Students are welcome to attend lunch at 12:00 p.m. if desired.

The training format is approximately 100% instructor-led lecture. For hands-on training, WEG offers longer, hands-on classes.